Our Business is still open.

Food safety and legionella thermometers for essential service providers are our priority. Extra cleaning and staff distancing is in place. Homeworking is enabled where possible.

TME-LEGK2-T-Type-Premier-Legionella-Temperature-Monitoring Kit-with-MM7000-2D

LEGK2 - T Type Premier Legionnaires Temperature Kit


LEGK4 - T Type Legionnaires Monitoring Kit with Dual Probe

LEGK3 - K Type Premier Legionnaires Kit with Dual Probe

Availability: In stock

Compatible Products


LEGK3 K Type Premier Water Temperature Testing Kit with MM7000-2D Barcode Scanning Thermometer, Dual Surface and Immersion Probe, Fine Wire Probe and accessories. Designed for use in monitoring the temperature of both running and standing water, as well as the surfaces of pipes and tanks that form part of a water system. The inclusion of the MM7000-2D Barcode Scanning thermometer enables the user to record locations, asset numbers and personalised temperature alarms.


MM7000-2D Handheld Thermometer

Measurement Range : -200 to + 1820°C (probe dependent)

High Accuracy ±0.2°C ±0.1% of Reading

Temperature Alarms: – user-programmable for personalised needs

Stores up to 1,000 readings

Readable 1D and 2D Bar Codes include (but not limited to): -All UPC/EAN/JAN Codes, QR Code, EAN29 Codes, Code 39 and Code 128

°C/°F Selectable

Switchable thermocouple Types K / T / J / R / N / E / S

IP65 Casing

Low Battery Indication

Rubber Boot included with the thermometer for extra protection against damage

Thermometer can be used with other 2-pin Thermocouple Probes


Measurement Range :


KS20-S* Dual Surface/Immersion Probe: -50 to 250°C

KA01 PTFE Thermocouple Fine Wire Sensor: -100 to 250°C

Probe measurements:


KS20-S* Dual Surface/Immersion Probe: 115mm x 12mm

KA01 PTFE Thermocouple Fine Wire Sensor: 1m x 0.3mm



TAPS – Thermocouple Attachment Pads. For use with fine wire probes to adhere the sensor to a pipe or tank and leave in situ. Can be used in temperatures from -50 to 250°C

LEGC01 – Keeps everything together and protected. Measures 34cm x 26cm x 6.5cm (approximate external) Holds up to 1 x Handheld thermometer, 2 x Straight Handled Temperature Probes, Fine Wire Probe and batteries.


MM7000-2D ThermoBarScan 1D/2D Barcode Scanning Thermometer with Bluetooth

KS20-S* High Speed Dual Probe

KA01 K Type PTFE Insulation Fine Wire Thermocouple

LEGC01 Carry Case

1 x PP3 Battery


* Note: This dual surface/immersion probe only requires light pressure to give a true reading and is suitable for smooth, clean surfaces.

If used on an uneven surface, there is a risk that the band will be weakened and deformed.

More Information
Compatible Products Link http://
Write Your Own Review
You're reviewing:LEGK3 - K Type Premier Legionnaires Kit with Dual Probe
Your Rating

Related Posts

Product Faqs

Ask a Question

Ask a Question

Sort by   
  • When is it important to use a thermometer?
    Question by: admin on 2018-09-05 11:54:29

    There are many different applications which require the use of a thermometer, from basic everyday tasks such as cooking or testing family members for a fever, to checking fridge/freezer/oven temperature, measuring water temperature to help prevent outbreaks of Legionnaires’ disease, reaching critical temperatures in a manufacturing process, maintaining temperatures during distribution of food products, tyre production, oil production, laboratory testing, facilities/building management and more. The risks of not having a thermometer for these applications vary from a burnt dinner to patients contracting a life-threatening disease.

    Answer by: admin on 2018-10-03 01:28:00
  • What is the difference between a thermometer and a probe?
    Question by: admin on 2018-09-05 11:51:38

    Simply put, the thermometer is the ‘box’, where you will see a screen that displays measurements, and the probe is the thing connected to it. So the probe (or sensor), senses the temperature and sends a signal to the thermometer, which translates it into a figure (usually °C or °F) and displays it. Probes can come in many different varieties which are designed to suit a specific application (such as needle probes, flat food probes, air probes etc). Thermometers, too, can have many different applications in addition to displaying a temperature reading. Some thermometers have a hold function, or can calibrate other thermometers, scan barcodes or wirelessly send temperature readings to other electronic equipment such as PCs or PDAs.

    Answer by: admin on 2018-10-03 01:30:05
  • How often should I calibrate my thermometer?
    Question by: admin on 2018-09-05 11:45:58

    Different Environmental Health Officers and HACCP Officers will require different levels of calibration. You should always follow the advice of your EHO on calibration. At TME, we are happy for the calibration of thermometers to be tested weekly, which you can do yourself. Most EHOs advise a yearly re-calibration of your thermometer and/or probe, which would consist of sending your thermometer away to be calibrated.

    Answer by: admin on 2018-10-03 02:13:22
  • What are the required water temperatures for buildings?
    Question by: admin on 2018-06-20 11:30:36

    To prevent an outbreak of Legionnaires’ disease, the HSE’s ACOP L8 recommends that hot water in a building should be stored above 60°C and distributed above 50°C, and cold water distributed below 20°C.

    Answer by: admin on 2018-06-20 11:30:36
  • What is Legionnaires’ disease?
    Question by: admin on 2018-06-20 11:15:34

    Legionnaires’ disease is a potentially fatal illness caused by the legionella bacterium, which may be present in tepid water and is spread by inhalation of fine water droplets or spray.

    Answer by: admin on 2018-06-20 11:15:34
  • Does my MM7000 range thermometer come with a battery?
    Question by: admin on 2018-06-19 14:57:11
  • How do I turn my MM7000 range thermometer on and off?
    Question by: admin on 2018-06-18 14:12:45
  • How do I assign barcodes to my temperature testing points?
    Question by: admin on 2018-06-18 14:04:43
  • What is a thermocouple thermometer?
    Question by: admin on 2018-06-18 13:22:07

    Thermocouple thermometers are the most widely used thermometer in the modern day. Thermocouples use electrical technology to show temperature. A thermocouple ‘couples’ together two different metals, one that is contained within the thermocouple thermometer, and one that forms a probe or sensor, to test the temperature of a substance or atmosphere. The difference in the temperatures of the two metals is expressed electrically through their different voltages. The temperature of the metal inside the thermocouple is already known, so the difference between the two temperatures allows us to easily deduce the temperature of the metal attached to the probe. The deduction is carried out using a microchip inside of the thermometer, and the temperature that the probe has sensed then shows on the display. Thermocouples are essential in many heating, manufacturing and electrical engineering applications, and can be found in different thermocouple types, according to the different metals used in the probes. Thermocouples have the advantage of a very fast response and large potential measurement range – from -270 to 1,800°C. TME thermocouple thermometers are compatible with several different thermocouple types (such as K/T/J/R/N/E/S). Most TME probes are in T type (for food applications) or K type (for non-food application), although we do manufacture probes in all different thermocouple types. In Summary ( Type T Thermocouple) Temperature range : Good Accuracy : Good Time Response : Good

    Answer by: admin on 2018-06-18 01:22:07
  • I regularly need to replace my thermometers and probes, can I set up a service contract to cover the cost?
    Question by: admin on 2018-06-18 12:41:03

    If you have purchased a large number of TME thermometers/probes, and are likely to have a high turnover of breakages, we offer a swap service which charges a set monthly rate in return for an unlimited number of swaps. We can offer this on a next day basis. If you are interested in the swap system, please phone or email TME for advice on how best to set it up.

    Answer by: admin on 2018-09-05 10:27:42
  • Why does the MM7000 range of thermometers use Barcode technology?
    Question by: admin on 2018-06-18 12:32:18
  • What is the warranty on my probe?
    Question by: admin on 2018-06-18 10:51:17

    TME probes do not come with a warranty, however, if there is a fault in our manufacturing process we will of course replace for free.

    Answer by: admin on 2018-09-05 10:25:13
  • Will you replace my thermometer if it is broken?
    Question by: admin on 2018-06-15 15:04:50

    We will. Details of our Thermometer for Life guarantee can be found as a downloadable pdf on the majority of our products that are or contain a thermometer. The scheme offers a repair/replacement of your thermometer at a fixed price, for life.

    Answer by: admin on 2019-06-05 01:17:33
  • Can I get a calibration certificate on this item?
    Question by: admin on 2018-06-15 09:53:42

    Yes. This would be for our standard UKAS traceable certificate. Prices start at £35.00. Please email sales@tmethermometers.com with the four temperature points required.

    Answer by: admin on 2018-10-03 01:31:48